Losi/TLR Truck Parts

Losi Tenacity SCT Body Mount Set

$10.99ITEM: LOS230036

Losi Tenacity SCT Body Mount Set

Overview:

This is a replacement Losi Tenacity SCT Body Mount Set.

Losi LST 3XL-E Limited Slip Differential Rebuild Kit

$16.99ITEM: LOS242027

Overview: This is a replacement Losi Limited Slip Differential Rebuild Kit for the LST 3XL-E.

Losi 8x14x4mm Flanged Rubber Sealed Ball Bearing

$17.99ITEM: LOSA6948

Overview: This is a pack of four 8x14x4 flanged rubber sealed ball bearings for the Losi 8IGHT racing buggy. These bearings are the internal bearings used in differential assemblies.

Losi Rear Bumper Set

$11.99ITEM: LOSB2417

Overview: This is a replacement Losi Rear Bumper Set, and is intended for use with the Losi TEN-SCTE.

RPM Losi Tenacity Front Skid Plate

$15.95ITEM: RPM73182

Overview: The RPM Losi Tenacity Front Skid Plate is designed to fit both the molded chassis version of the Tenacity as well as the aluminum chassis option. RPM skid plates are Made in the USA from RPM's incredibly tough blend of engineering grade nylons for performance you can count on. Molded Chassis versions of the Tenacity A key breakage area of the molded Tenacity chassis reported to RPM engineers is the area located just behind the front bulkhead mounting screws. By tying together the four bulkhead mounting screws with the two screws holding the steering mounting posts in place, RPM has beefed up the strength and durability of the entire front end of the chassis, helping to reduce that pesky breakage problem while adding some much needed abrasion resistance to the chassis. Aluminum Chassis versions of the Tenacity MSRP on a new aluminum chassis for the Tenacity is $55.99. It only makes sense to protect that chassis for as long as possible. What better way is there than a product specifically designed to reduce skid and abrasion resistance? RPM skid plates will not only increase the longevity of your valuable aluminum chassis, they’ll also significantly reduce the amount of scuffs and scratches it’ll receive since these skid plates are the lowest impact point on the chassis NOTE: RPM skid plates fit LOS231023 molded chassis versions and LOS231056 aluminum chassis versions of the Tenacity (SCT, T & DB). Not for use on MT versions.

Team Losi Racing Front Shock Tower & Body Mount Set

$8.99ITEM: TLR1102

Team Losi Racing Front Shock Tower & Body Mount Set

Overview:

This is a replacement Team Losi Racing Front Shock Tower & Body Mount Set, and is intended for use with the TLR 22T 1/10 stadium truck.

Team Losi Racing Mud Guard w/Side Guard

$10.99ITEM: TLR231000

Overview: This is a replacement Team Losi Racing Mug Guard Set, and is intended for use with the Team Losi Racing TEN-SCTE 2.0 1/10 scale 4WD short course truck. This package also includes two side guards.

Team Losi Racing 8IGHT-X Aluminum Throttle Servo Horn (23T)

$19.99ITEM: TLR341015

Team Losi Racing 8IGHT-X Aluminum Throttle Servo Horn (23T)

Overview:

This is an optional Team Losi Racing 8IGHT-X Aluminum 23T Throttle Servo Horn, intended for use with the 8IGHT-X 1/8 4WD Competition Nitro Buggy and the 8IGHT-X 1/8 4WD Elite Competition Nitro Buggy kits.

Team Losi Racing Mud Flaps (2)

$4.99ITEM: TLR4007

Overview: This is a pack of two replacement Team Losi Racing Mud Flaps.

Team Losi Racing Hi Performance Pre-Cut Body (Clear)

$46.99ITEM: TLR8061

Overview: This is an optional Team Losi Racing Hi-Performance Clear Short Course Body. This aftermarket body will improve the performance of the Losi XXX-SCT, Ten-SCTE, Team Losi Racing 22SCT or any other 1/10 scale short course truck by allowing air to pass through release holes in the body during flight. This will reduce the "parachute effect" and improve downforce and stability for excellent high and low speed cornering. This body has been trimmed at the factory and has all the air release holes pre-cut! No need to perform this tedious and time consuming task any longer. Features: - Designed and tested for high performance handling - Specially designed air outlets reduce the "parachute effect" by directing the flow of air outward, providing improved jumping and air handling characteristics - High downforce design for improved corner speed, stability, and improved drivability - Pre-cut eliminating the need for the tedious and time consuming process to be done by hand - .040" Lexan for improved reliability and durability - Covered by a thin film that prevents over-spray from effecting the outside of the body - Pre-cut Window Masks included - TLR, grill, and tail light sticker sheet included - Side dams and hardware included - Clear body, requires painting