Flight Controllers & Boards

AfroFlight Naze32 Rev5 Acro FunFly Controller

$39.99ITEM: AFRONAZE32

Initially designed for use with small to mid-sized multirotor craft, it has become the go-to controller for a host of Multirotor projects and propheads.

The infamous Hamasaki AKA “timecop” was not happy with the limitations and performance an 8-bit MCU could deliver on current FC platforms, so he set out to make a flight controller that could take just about any demands a developer could throw at it, and thus was born the Naze32. At the heart of the Naze32 is a 32bit ST micro work horse of a processer, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration.

The Naze32 comes as the most complete Acro Version yet, with both strait and 90deg pins for your preference and a matched break out harness.

FEATURES:
• Flexible motor outputs, support various airframe types:
Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
• Up to 8 ch RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spektrum satellite receivers.
• Built in FrSky telemetry inverter (shared w/main port)
• Battery voltage monitoring
• Modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
• Onboard MicroUSB for setup and configuration
• LEDs so bright, they could blind you
• MultiWii-based configuration software for easy setup
• rev5 hardware

DYS Power Distribution Board 10-20V

$9.00ITEM: DY-PDB

DYS Power Distribution Board 10-20V

• Output power for variable voltage 10-20V, 36W
• Output power for module 5V, 15W

F3 FEMTO FLIGHT CONTROLLER

$24.49ITEM: EMX-FC-1710

FEATURES/SPECS:

• STM32F303 CPU
• MPU9250 accelerometer/gyro/compass (connected via SPI)
• 2-6S LiPo battery
• Integrated 5V/3A BEC
• Dedicated Sbus and serial RX with 5v ,Spektrum 1024/2048, SBUS, XBUS, SumD and SumH RX with built-in inverter
• 6Supports direct connection of 3.3v Spektrum Satellite receivers
• Telemetry support (frsky telemetry, smartport, and HoTT telemetry)
• Dedicated PPM receiver input
• Buzzer support
• Dedicated output for programmable LEDs - great for orientation, racing and night flying. (Currently mutually exclusive with the Transponder)
• BLHeli Passthrough ready(connect BLheli suite)
• 2.0 mm pin headers
• 80A Current tolerance (PDB)
• Integrated Battery monitoring
• Use all the features all the time; e.g. Connect your USB + SmartPort + SBus + LED Strip + Battery Monitoring + 4 motors - all at the same time!
• 20x20mm board
• Weight 2.2 grams

UART3 (RX3)
Use for Spektrum Satellite RX, Spektrum 1024/2048, SBUS, XBUS, SumD and SumH RX, etc.

UART2/PPM - Serial RX or PPM RX + Telemetry
Use RX2 as PPM receiver. Use TX2 as telemetry output when using PPM.

Emax Bullet 35a Pro Edition

$14.99ITEM: EMX-SC-2044

EMAX BULLET 35A PRO EDITION

DYS F4 Pro Flight Controller 2-6S

$38.50ITEM: F4PRO

The DYS F4 Pro V2 Flight Controller features a powerful F4 based processor, MPU6000 gyro, build in PDB, OSD, Current Meter, & simple plug in inputs for DYS 4-in-1 ESCs. The F4 based processor gives pilots plenty of CPU headroom to activate all kinds of features within Betaflight, ensuring you will not have any desyncs from running too many options!

Features:
• Utilizes Ombibus F4 Firmware
• STM32F405 GRT6 Processor - Refresh Rate up to 8k
• 3oz PDB ensures stable current and excellent head dissipation
• 5V 3A BEC output
• Easy Soldering Pads
• Compatible with all ESC options; including DYS 4-in-1 without soldering
• Integrated OSD
• Integrated Current Sensor
• PID Adjustments via OSD
• VTX adjustments; Smart Audio required!
• Includes Rubber Mounting Grommets
• 2-6s LiPo Support

Lumenier F4 AIO Flight Controller (F4, OSD, PDB, Curr., V.Reg.)

$44.99ITEM: GF6740

The Lumenier F4 AIO Flight Controller combines a STM32F4 MCU, Betaflight OSD, full PDB, 12v 3A and 5v 3A BEC, Current Sensor, all in 1 compact package and weighing only 10g! Like other Betaflight OSD enabled flight controllers, you’ll be able to tune your PID’s using your transmitter and use the drag and drop OSD setup in the OSD tab of the BetaFlight Configurator.

• STM32F4 MCU (Spi connected to Gyro)
• Built in PDB for direct connect of ESC power and signal wires
• Built in high current bar
• Direct battery connect 3-6S with filtered Output of 5v 3A, 12v 3A
• SBUS/PPM + DSMX Ports
• SPI Gyro MPU6000
• On-Board Drag and Drop OSD (controlled by BetaFlight, FC over SPI bus)
• Onboard SD Memory for Blackbox
• Built-in Current Sensor (~140A)
• 3x UART
• Buzzer output
• WS2812B LED output

Lumenier SKITZO Flight Controller Powered by RaceFlight

$44.99ITEM: GF6876

The Lumenier SKITZO Flight Controller Powered by RaceFlight is the most advanced, performance driven, flight controller ever designed. The SKITZO Flight Controller was created in collaboration with and named after the flow master himself SKITZO FPV. Capable of running 32kHz gyro sample rate, PID loop, motor loop and processing all calculations in real time. The SKITZO FC is powered by the same hardware as the new RaceFlight Revolt which has incredible performance. The Lumenier SKITZO Flight Controller uses a F405 MPU and a Invensense 20602 gyro in combination with RaceFlight software to give you the BEST performance possible. This gyro is by far the most noise free and accurate gyro available.

Performance
The Lumenier SKITZO Flight Controller Powered by RaceFlight presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. The filters allow your quad to stay in the air no matter what! Damaged propellers caused by that insane gate clip on turn 3? Not a problem. You can still finish the race! For most people tuning is not even required. Our boards come preloaded with software and defaults that should fly amazing for 99% of people.

In addition to the vibration rejection technology, the gyro gives you the highest speeds currently possible with the lowest noise floor and highest sensitivity.

Software
This flight controller comes pre-loaded with the latest RaceFlight Community release. Just go to the google store and download the latest configurator, and you should be ready to connect. Drivers should no longer be needed.

Also, this custom SKITZO version will have special access to SKITZO Tuning settings as well as a special support channel where you can ask SKITZO questions about setup and recommendations. Each FC has a unique serial ID which will grant you access to these special features.

RaceFlight One is also available in alpha format. Just join the slack at http://raceflight.net/invite/ and ask to be added to the RaceFlight One channel. This is truly amazing software, which flies so well you can completely eliminate prop wash. Setup is a breeze as well, just run a couple wizards and you will get right up into the air.

Setup Simplicity
Setting up the Lumenier SKITZO Flight Controller is easy. The solder pin layout is easy to read with motor connections in each corner. Just solder the closest motors and remember the order 1, 2, 3, 4. Select your voltage on the bottom, as well as inverted or not. The SKITZO FC also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.

For step by step setup instructions and FAQs, please visit the RaceFlight website here.

FEATURES
• Supports the new RF1 firmware
• Integrated vibration dampening dummies
• Custom SKITZO color and silk screen
• Dual inverters for taranis and futaba radios
• True hardware radio diversity
• Selectable voltage for your UARTs
• LED Driver for WS2812b programmable LED
• Infrared LED Race Transponder support – no need for separate transponder
• Future iPhone and Android configurator support
• High Speed 32khz gyro, lowest noise floor and highest sensitivity gyro ever used
• Through hole solder pads – forms an I-Beam when soldered for extra strength
• FrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio support
• Integrated buzzer driver
• Voltage and current ADC pins, for full voltage and current monitoring
• Full telemetry output support
• ESC flashing and configuration built into configurator
• Most active software development
• Selectable 3.3v or 5v voltage
• 4 serial uarts
• Bluetooth expandable
• F4 processor
• 16mb of flash memory
• GPS expandable
• Dimensions: 36mm x 36mm
• Mounting holes: 30.5mm squared to center of holes

Power Distribution Board for For OCTO Multicopter by DYS

$13.00ITEM: OCTO-PDB

SPECIFICATIONS
Item No.: OCTO-PDB
Up to 8 ESC/Motor can be connect to the Board
260A (Continuous), 320A (Peak)
2 layout with 2oz(70um) Copper Dual PCB.
Gold plated with black soldermask
64mm body mounting1 PCB plate for(+), 1 PCB plate for(-)
Weight : 85g
Size : 105mm x 105mm
For OCTO Multicopter (Equipped with 16 pair of 3.5mm plug)

Hobby King Quadcopter Power Distribution Board

$7.99ITEM: PWRDISTBRD

Designed in house by the HobbyKing Enginerds, this handy power distribution board has the same foot print as our Multri-rotor control boards and is the ultimate solution for tidy power distribution wiring. Simply use 3.5mm male connectors on your ESCs and plug a battery in. The PCB is Gold plated for optimality efficiency and also features a bling port (aka 2 pin JST size auxiliary power out) Perfect for powering LEDs or any accessory fitted to your Quadcopter.

Emax 2306 2400kv Race Edition

$19.99ITEM: RS2306-2

EMAX 2306 2400KV RACE EDITION

Emax 2306 2550kv Race Edition

$19.99ITEM: RS2306-25

EMAX 2306 2550KV RACE EDITION

FC32 Flight Controller Rev 6 w/SPM RX Connector

$18.00ITEM: SPMFC3206

Features:
• USB on right side
• PPM/PWM input as through-hole
• 3.3V, I2C on standard-size headers
• Fully pinout compatible with rev5 accessories
• SBUS Inverter
• Compatible with Spektrum diversity rx
• MPU6500
• Sonar pads w/resistors added for direct connection
• All extra pads (FT, GP, A5) on top, only sonar on bottom
• BMP280 barometer
• 16mbit flash

Power Distribution Board with 5v and 12v regulator

$9.99ITEM: SPMVX9909

The 12 volt power supply will output approximately 1 volt less than the input voltage when the input voltage is less than 13v. This circuit does not boost voltage if the battery input voltage is less than 12v.

Features:
• A power distribution board intended to stack with flight controllers that feature a square 30.5mm mounting pattern such as the SPMFC3206, SPMFCF400, SPRF3, Revolt, Naze, CC3D and others
• Suitable for 250 mini racing drone quadcopters, such as the Blade Theory X, QAV250, tarot 250, ARRIS FPV 250, etc.
• Weight: 6g
• Two regulated outputs, 5V and 12V*
• LED switch (LED power supply is not voltage regulated)

DYS Power Distribution Board w/ Clean Flight

$56.60ITEM: XDRF3

Features:
• F3 Flight control, OSD, UBEC and the power distribution board to integrate into a PCB board
• A debug function to minimize the difficulties in installation and debugging when pairing with various quadcopters
• A PCB board with multiple layers of copper foil and solder pad, making it easier to minimize interference and draw more current
• Easy to upgrade the PCB board's firmware
• F3 clean flight has more connectors and makes it easier for pilots to expand their peripherals